Full Project – THE FABRICATION FOR A SET OF SIEVES AND SAKER
Click here to Get this Complete Project Chapter 1-5
ABSTRACT
The fabrication of a set of sieves and shaker was carried out in paliton workshop, Enugu. After a thorough analysis on the suitable materials to be used in fabrication, galvanized steel was chosen due to its advantages over materials of fabrication. The fabrication was carried out in order to analyze the sizes of particles. The component parts of the sets of sieve and their dimensions are as follows:
Height of sieve 5.5cm
Number of sieves 7
Diameter of sieve 13.5cm
Shape of sieve circular
Height of sieve set 44cm
In fabricating this set of sieves, some factors were taken into consideration and they are:
The capacity of the sieve.
The type of mixture that can be filtered in it.
The types of properties and composition of the mixture.
The type of material to be used for fabrication of the sieve and shaker.
The mechanism of the filtration process and also,
The cost, which is the determinant, factor in fabrication of any equipment.
These factors help greatly in the fulfillment of the objective of this project study. And after fabrication the projects were tested and seem to be working very efficiently with a reasonable separation of particle and cut diameter.
Using the above dimensions, the following fabrication procedures were undertaken, layout, cutting, drilling, welding, filling sand papering, washing and painting, drying assembling.
Finally, the set of sieves and shaker were subjected to the process of washing, painting and drying.
TABLE OF CONTENT
Title page
Approval page
Letter of transmittal
Dedication
Acknowledgement
Abstract
Table of content
CHAPTER ONE
1.0 INTRODUCTION
CHAPTER TWO
2.0 LITRATURE REVIEW
2.1 Model
2.2 Screening
2.3 Types of screens
2.4 Screen surface
2.5 Factors in selecting screen equipment
2.6 Method of feed
CHAPTER THREE
3.0 MATERIAL OF CONSTRUCTION
3.1 Aluminum and aluminum alloy
3.2 Carbon and low alloys steel
3.3 Corrosion
3.4 Contact or galvanic corrosion
CHAPTER FOUR
4.0 FABRICATIONAL PROCEDURE
4.1 Layout
4.2 Cutting
4.3 Drilling
4.4 Welding
4.5 Filling
4.6 Sand papering
4.7 Washing and painting
4.8 Drying
4.9 Assembling
CHAPTER FIVE
5.0 OPERATION AND MANTENANCE
5.1 Function of some parts of the electrically vibrated screen.
CHAPTER SIX
6.0 RECOMMENDATION AND CONCLUSION
6.1 Costing
REFERENCE.
CHAPTER ONE
1.0 INTRODUCTION
Generally, all engineering aspects involve fabrication more especially for chemical plants or equipment, which are used for several processes. This fabrication is carried out so as to achieve and put to practice chemical processes with the help of some components for equipment used for the fabrication procedures enables engineers to deal with operations for separating the component of a mixture, which is automatically based on particle size analysis of materials from one particular sieve to another.
Chemical engineering mostly deals with the fabrication of sieve among other fabrication in order to fulfil the theory of separation technique. In separation processes especially particle size analysis is where sieving technique are available.
During the operation of particle size analysis, many types of screen can be involves, which include Grizzy screens, Revolving screens, mechanical shaking screens, vibrating screen, electrically vibrated screens, oscillating screen, Reciprocating screens and Gyratory screens.
As this project involves the fabrication of set of sieves, it therefore requires good layout and easy separation of oversize and undersize in the contacting sieve unit.
Moreover, in the fabrication of set if sieves, we have to bear certain qualities in mind in which the set of sieves will have to portray such as determination of size and shape of the equipment, which contributes to the efficiency of the equipment. Among the above aim, the set of sieves should be considerable in terms of costing and also availability and portability of the set of sieve should be considered.
Above all, the set of sieve is fabricated in such a way that the particle of larger size than that of the sieve will be retained on the sieve while the particle of lower size will pass through the sieve and be collected on and9othet sieve as undersize, which is also separated by that sieve
Get the Complete Project
This is a premium project material and the complete research project plus questionnaires and references can be gotten at an affordable rate of N3,000 for Nigerian clients and $8 for International clients.
Click here to Get this Complete Project Chapter 1-5
You can also check other Research Project here:
- Accounting Research Project
- Adult Education
- Agricultural Science
- Banking & Finance
- Biblical Theology & CRS
- Biblical Theology and CRS
- Biology Education
- Business Administration
- Computer Engineering Project
- Computer Science 2
- Criminology Research Project
- Early Childhood Education
- Economic Education
- Education Research Project
- Educational Administration and Planning Research Project
- English
- English Education
- Entrepreneurship
- Environmental Sciences Research Project
- Guidance and Counselling Research Project
- History Education
- Human Kinetics and Health Education
- Management
- Maritime and Transportation
- Marketing
- Marketing Research Project 2
- Mass Communication
- Mathematics Education
- Medical Biochemistry Project
- Organizational Behaviour
- Political Science
- Psychology
- Public Administration
- Public Health Research Project
- More Research Project
- Transportation Management
- Nursing
Full Project – THE FABRICATION FOR A SET OF SIEVES AND SAKER